Air Tools

  Chih Tai Y&S Co., Ltd.

   No.20, Lane 70, Sec.5, Yang-Hai Rd., Fu-Hsing Hsiang, Changhua, Taiwan

   Tel:886-4-7764112  7771377  Fax: 886-4-7771692 

   P.O.Box: 107 Lukang         E-mail: chihtai@ms16.hinet.net  

   Search our site of over 10,000 items   


Contact Us


Home

Air Tools
Auto Tools
Socket Sets
Gear Wrench and Wrench
Fluid/Oil extractor
Motor Cycle Tools
Cordless Tools
Ratchet Handle
Straps and Ratchet Tie Down

New Products

ˇ@

ˇ@

Engine and Belt Tools Piston and Brake Tools Valve Seal Tool Crank Bearing Install and Puller Tools Oil Tools
Chain Puller and Install Tools Flywheel Puller Tools Pulley Holder Tools Wrench Tool Fork and Shock Tools Motorcycle | Motorbike Tools Kit Clutch Tools Tire and Wheel Tools Other Tools and Accessories Steering Tools

Steering Tools (Motorcycle Tools)

Bearing Oil Seal Install Tool

CH040936
Bearing Oil Seal Install Tool


Bearing Install Tool

CH040937
Bearing Install Tool


Oil Seal Install Tool

CH040938
Oil Seal Install Tool


CH040913-3
Front Suspension Oil Seal Tool


Suspension Tool

CH040913
Suspension Tool


ˇ@


CH152055

Steering Stem Bearing Race Removal Tool

 

* It provides a simple way to remove the bearing race on a steering stem.

* It works on most all stems.

* Opening sizeˇG30mm ~ 68mm

 

Instruction:

* Insert it into the stem.

* Open it up until it is tight against the stem.

* From the other end tap the tool out the lip on the tool. (as shown in figure)

* And then, it will catch the race and pull it through.

 


Front Suspension Tool

CH040966
Front Suspension Tool
Range: 35-47mm


ˇ@


CH1520122

Steering stem nut tool <For Ducati>

 

* It enables you to correctly torque the steering stem nut.

* It is designed to be used with a 3/8 inch drive.

* It fits all 4V Superbikes, Multistrada, Hypermotard and other models with the large diameter steering stem nut.

* The rubber cushion design allows you without damaging the steering stem nut in the process of removal and installation.

* MaterialˇG6061-T6 aluminum

 

Note:

* Remove the upper triple clamp from the steering stem nut and the fork tubes before loosening or tightening your steering stem nut.

* The torque procedure is critical and must be completed correctly, make reference to the service manual for your bike model before use or take it to a qualified repair shop for installation.

 


ˇ@


Gear Nut Tool

CH040943
Gear Nut Tool


CH152044

Swing arm Bearing Tool 

 

* Designed for installation of the swing arm bearings on Honda, Suzuki, Kawasaki and Yamaha from 1990 through 2000.

* This tool provides 3 necessary drivers to fit the main swing arm needle bearings.

* Allows user to push bearing into the swing arm easily.

Parts list:
ˇ@

Description

Qˇ¦ty

Threaded rod

1

Thrust bearing

1

Driver 1 (22.0mm/26.8mm)

1

Driver 2 (21.0mm/26.0mm)

1

Driver 3 (20.0mm/26.0mm)

1

Large washer

1

Small washer

1

Nut

2


Steering Bearing Attachment Tool

CH040909
Steering Bearing Attachment Tool


Steering Attachment Tool

CH040909-N
Steering Attachment Tool


Steering Nut Tool

CH040909-5
Steering Nut Tool

CH040909-51, 4teeth 30mm
CH040909-52, 4teeth 32mm
CH040909-53, 4teeth 34mm
CH040909-54, 4teeth 38mm
CH040909-55, 4teeth 41mm
CH040909-56, 3teeth
CH040909-57, 6teeth
CH040909-58, 8 point 32mm
CH040909-59, long type 6 points 32mm


Steering Nut Tool

CH040922
Steering Nut Tool


Steering Nut Tool

CH040964
Steering Nut Tool
6 Gear


Steering Nut Tool 4 gear

CH040964-4
Steering Nut Tool

4 Gear


Steering Bearing Nut Tool

Steering Bearing Nut Tool

CH040956,  size:dia.30 x 175L
CH040956-34,  size:dia.34 x 175L
CH040956-38,  size:dia.38 x 175L


Steering Bearing Shock Tool

Steering Bearing Shock Tool
CH040963

Including:
*1pc steering bearing shock:500L
*4pcs attachment:dia.24,27,30,31


Front Suspension Nut Tool

CH040972-0812
Front Suspension Nut Tool


Front Suspension Nut Tool

CH040972-1014
Front Suspension Nut Tool


Item No.: CH080775
Hex Axle Tool

Fit internal hex on many late model sport bike and some off-road applications.
Size : 17,19,22and 24mm.3/8ˇ¨ Dr. square drive
Material:SCM440


Hex Axle Tool


CH0915223-1
Hex Axle Tool


Fit internal hex on many late model sportbikes and some off-road applications.
Size : 17,19,22and 24mm.3/8ˇ¨ Dr. square drive


Hex Axle Tool

CH080775-1
Hex Axle Tool
 

Description:
* Fit internal hex on many late model sportbikes and some off-road applications.

* Size : 14,12,17,19,22and 24mm.


CH1520149

Axle Nut Wrench

 

* Ideal tool to install and remove front wheel axles and swing arm pivot shafts.

* Double sided 19 mm and 24 mm hex.

* It also provides a 3/8ˇ¨ square drive hole in the handle for easy torque adjustments.

* Works on Honda, Kawasaki, Suzuki, and Yamaha.


Hook Wrench

CH040908
Hook Wrench

Size: dia. 42 x 40


Hook Wrench

CH040910
Hook Wrench

Size: dia. 60 x 65


Steering Bearing Nut Wrench

CH040958
Steering Bearing Nut Wrench

Size:53mm


Steering Bearing Nut Wrench

CH040958-46
Steering Bearing Nut Wrench

Size:46mm


Aluminum Vise Insert

CH152054

Aluminum Vise Insert

It is an essential tool for every mechanicˇ¦s workbench.
Aluminum jaws provide three machined openings to hold
5/16ˇ¨ to 9/16ˇ¨ (7mm to 15mm) axles for easy wheel hub and
pedal adjustments securely without damage axle threads.
The bridge spring keeps the jaws aligned and allows the tool
to automatically open.


ˇ@

  Chih Tai Y&S Co., Ltd.

   No.20, Lane 70, Sec.5, Yang-Hai Rd., Fu-Hsing Hsiang, Changhua, Taiwan

   Tel:886-4-7764112  7771377  Fax: 886-4-7771692 

   P.O.Box: 107 Lukang         E-mail: chihtai@ms16.hinet.net  


Copyright © 2007 Chih-Tai Y&S Company Ltd.

ˇ@

ˇ@