Air Tools

  Chih Tai Y&S Co., Ltd.

   No.20, Lane 70, Sec.5, Yang-Hai Rd., Fu-Hsing Hsiang, Changhua, Taiwan

   Tel:886-4-7764112  7771377  Fax: 886-4-7771692 

   P.O.Box: 107 Lukang         E-mail: chihtai@ms16.hinet.net  

   Search our site of over 10,000 items   


Contact Us


Home

Air Tools
Auto Tools
Socket Sets
Gear Wrench and Wrench
Fluid/Oil extractor
Motor Cycle Tools
Cordless Tools
Ratchet Handle
Straps and Ratchet Tie Down

New Products

 

 

Engine and Belt Tools Piston and Brake Tools Valve Seal Tool Crank Bearing Install and Puller Tools Oil Tools
Chain Puller and Install Tools Flywheel Puller Tools Pulley Holder Tools Wrench Tool Fork and Shock Tools Motorcycle | Motorbike Tools Kit Clutch Tools Tire and Wheel Tools Other Tools and Accessories Steering Tools

Crank Bearing Install Puller Tools (Motorcycle Tools)


CRANK BEARING & GEAR PULLER / INSTALL TOOL

CH040948

Crank Bearing & Gear Install Tool

Including:
*Bearing size:dia.22 & 25(ID.), dia.56(OD.) +puller
*Gearing size:dia.22 & 25(ID.) +shock
*Bearing Gear Shock dia.22 & 25(ID.) (only to close)

 


CH080794
 

Motorcycle Turn Handle Bearing with Slide Hammer Shaft 390MM

 

35-40/40-45/43-48/46-51


BLIND BEARING PULLER

CH080706
BLIND BEARING PULLER 
SET,8/10/12/15/17/20/25/30mm

Contents:

Shaft: Slide hammer shaft 390mm/L

Hammer: hammer weight 100mm/L-2.15LB(940g)

8mm: 5/16"to13/32"(8-10mm)

10mm: 13/32"to15/32"(10-12mm)

12mm: 15/32"to9/16"(12-14mm)

15mm: 19/32"to11/16"(15-17mm)

17mm: 11/16"to25/32"(17-20mm)

20mm: 25/32"to15/16"(20-24mm)

25mm: 1"to1-1/8"(25-29mm)

30mm: 1-3/16"to1-1/4"(30-32mm)


Bearing remover Set

CH080755
Bearing remover Set

SIZE: 9.8mm, 11.8mm, 14.8mm, 16.8mm, 18.8mm, 19.8mm, 24.8mm


Click Picture to EnlargePilot Bearing Puller 3 Jaws

CH091008
Pilot Bearing Puller 3 Jaws
*Capacity: inside diameter 13mm-38mm (1/2"-1 1/2")
*Ideal for:
1)Automotive flywheel
2)Motorcycle wheel
3)Bicycle wheel
4)Pump bearing
5)Generator bearing
6)Machine bearing etc.

Pilot Bearing Puller 3 Jaws

Steering Stem Bearing Race Removal Tool

CH152055
Steering Stem Bearing Race Removal Tool

It provides a simple way to remove the bearing race
on a steering stem.
It works on most all stems.
Opening size:30mm ~ 68mm
1.  Insert it into the stem.
2.  Open it up until it is tight against the stem.
3.   From the other end tap the tool out the lip on the tool. (as shown in figure)
And then, it will catch the race and pull it through.


Steering Bearing Installation Tool <For Motorcycles>

CH152062
 

Steering Bearing Installation Tool <For Motorcycles>

Click to enlarge picture 

 


Timing And Crankshaft Turning Tool <for Ducati>

CH152063

Timing And Crankshaft Turning Tool <for Ducati>

 

Click to enlarge picture


Crankcase Separator Tool

CH152065
Crankcase Separator Tool

It fits most 2-stroke & 4-stroke engines with
vertically split cases.
It allows a multitude of bolt patterns to be used.
It eliminates binding under heavy loads.
It provides 6mm mounting bolts (M6 x 1.0 x 200),
8mm mounting bolts (M8 x 1.25 x 200) and crankcase
separator center bolt with 24mm hex.


Universal Crankshaft Installation Set

CH152067
Universal Crankshaft Installation Set

It is ideal tool for installation the crankshaft into crankcase.
Fits most single cylinder vertically split engines.
Set consists of one installing pot, one pot spacer, one bolt
with nut and 11 different size adapters.
All adapters are made from CrMo steel.
Except for M12x1.25, all adapters have right hand threads.
Sizes as follows:M7x1.0、M10x1.25、M12x1.25、M12x1.0、M12x1.25、
M14x1.0、M16x1.0、M18x1.0、M14x1.5、M10x1.25、M22x1.0(for
Yamaha YFM200/250/350/400 ATV)


Heavy-Duty hole bearing puller set

CH080706-N

Heavy-Duty hole bearing puller set


Utensilb per compression steering pace press set

Item No.: CH080777

Utensilb per compression steering pace press set


Steering tube bearing insealler set

Item No.: CH080776

Steering tube bearing insealler set

 


Crank Install Puller


CH040907-P
Crank Install Puller (7pcs)


Including:
*1pc crimp nut
*1pc lock ring
*1pc attachment
*2pcs support 10mm x 30cm
 


Crank Install Puller (7pcs)

 

CH040907
Crank Install Puller (7pcs)

 

 

 



CH152050

Bearing Retainer Tool 

 

* Designed to remove and install the rear wheel seal/bearing retainer ring, and prevent damage to the retainer ring.

* 22mm external hex head and 3/8” square drive.

* Material: SCM415

 

Applications:

* XR650L 93-07, XR600R 85-00, XR500 79-84, XR350R 83-85, XR250R 84-95, XR200R 81-02, XL200R 83-84, XL250K 72-76, MR250 76, CR250M 76


Crank Box Tool

 

CH040929
Crank Box Tool

 


Crank Box Tool Set

 

CH040929-1
Crank Box Tool Set


Including:
*CH040929
*3pcs 6mm x 125L
*3pcs 8mm x 125L

 



CH091533-M2
Crankcase Puller


This set included 6mm &8mm bolt:
*3pcs 8mm mounting bolt
*3pcs 6mm extension adaptor

Will work on most 2&4 stroke engine with vertically split cases
Multitude of blot patterns to be used.
 


Crank Bearing Puller

 

CH040904
Crank Bearing Puller

 

 

 


Heavy Duty Crank Pulley Puller

CH040927-1
Heavy Duty Crank Pulley Puller

 


Crank Gear Nut

 

CH040973
Crank Gear Nut

 

 

 


Heavy Duty Crank Pulley Puller

 

CH040927-2
Heavy Duty Crank Pulley Puller

 

 

 

 


Bearing Puller Tool

 

CH040920-30
Bearing Puller Tool

Size:8,10,12,15,17,20,25,30mm

 

 

 


Bearing Puller Tool

 

CH040920-25
Bearing Puller Tool


Size:8,10,12,15,17,20,25mm

 

 

 

 


Bearing Puller Tool

 

CH040920-32
Bearing Puller Tool

Size:8,10,12,15,17,20,25,30,32mm

 

 

 

 


Bearing Puller Tool

 

CH040920-35
Bearing Puller Tool


Size:8,10,12,15,17,20,25,30,32,35mm

 

 

 

 


Bearing Puller Tool

 

CH040920-45
Bearing Puller Tool


Size:8,10,12,15,17,20,22,25,30,32,35,40,45mm

 

 

 

 


Bearing Puller Tool

 

CH040975
Bearing Puller Tool


Size:8,10,12,15,17,20,25,30mm

 

 

 


Bearing Puller Tool

 

CH040976
Bearing Puller Tool


Size:8,10,12,15,17,20,22,25,30mm

 

 

 


Sliding Hammer

 

Sliding Hammer

CH040951-42, size:42mm
CH040951-48, size:48mm

*1/2 x W12 x 395mm
 


Bearing Shock Tool

 

CH040962
Bearing Shock Tool

 

 


Engine Center Washer Tool

 

Engine Center Washer Tool

CH040955-2017, size:20mm x 17mm
CH040955-3028, size:30mm x 28mm
CH040955-37, size:34mm
CH040955-40, size:40mm

 


Bearing Attachment Inside


Bearing Attachment Inside


CH040974-8, size:8mm
CH040974-10, size:10mm
CH040974-12, size:12mm
CH040974-15, size:15mm
CH040974-17, size:17mm
CH040974-20, size:20mm
CH040974-22, size:22mm
CH040974-25, size:25mm
CH040974-30, size:30mm
CH040974-32, size:32mm
CH040974-35, size:35mm
CH040974-40, size:40mm
 


 

  Chih Tai Y&S Co., Ltd.

   No.20, Lane 70, Sec.5, Yang-Hai Rd., Fu-Hsing Hsiang, Changhua, Taiwan

   Tel:886-4-7764112  7771377  Fax: 886-4-7771692 

   P.O.Box: 107 Lukang         E-mail: chihtai@ms16.hinet.net  


Copyright © 2007 Chih-Tai Y&S Company Ltd.